eng
Islamic Azad University Arak Branch
Journal of Solid Mechanics
2008-3505
2008-7683
2011-03-30
3
1
1
8
514395
Curvature Effects on Thermal Buckling Load of DWCNT Under Axial Compression Force
A Ghorbanpour Arani
aghorban@kashanu.ac.ir
1
M Mohammadimehr
2
M Ghazi
3
Department of Mechanical Engineering, Faculty of Engineering, University of Kashan---- Institute of Nanoscience & Nanotechnology, University of Kashan
Department of Mechanical Engineering, Faculty of Engineering, University of Kashan
Department of Mechanical Engineering, Faculty of Engineering, University of Kashan
In this article, curvature effects on elastic thermal buckling of double-walled carbon nanotubes under axially compressed force are investigated using cylindrical shell model. Also, the small scale effect is taken into account in the formulation. The dependence of the interlayer van der Waals (vdW) pressure on the change of the curvatures of the inner and outer tubes at that point is considered. The effects of the surrounding elastic medium, curvature and the vdW forces between the inner and outer tubes increase the critical buckling load under thermal and axial compression loads, while small scale effect decreases it.
http://jsm.iau-arak.ac.ir/article_514395_66be5be85feaacf96e9e35805f9212b6.pdf
Curvature effect
Thermal buckling load
Small scale effect
Axial compression force
DWCNT
eng
Islamic Azad University Arak Branch
Journal of Solid Mechanics
2008-3505
2008-7683
2011-03-30
3
1
9
18
514396
Magneto-Thermo-Elastic Behavior of Cylinder Reinforced with FG SWCNTs Under Transient Thermal Field
A Ghorbanpour Arani
aghorban@kashanu.ac.ir
1
M.R Mozdianfard
2
V Sadooghi
3
M Mohammadimehr
4
R Kolahchi
5
Department of Mechanical Engineering, Faculty of Engineering, University of Kashan---- Institute of Nano science & Nanotechnology, University of Kashan
Department of Chemical Engineering, Faculty of Engineering, University of Kashan
Department of Mechanical Engineering, Faculty of Engineering, University of Kashan
Department of Mechanical Engineering, Faculty of Engineering, University of Kashan
Department of Mechanical Engineering, Faculty of Engineering, University of Kashan
In this article, magneto-thermo-elastic stresses and perturbation of magnetic field vector are analyzed for a thick-walled cylinder made from polystyrene, reinforced with functionally graded (FG) single-walled carbon nanotubes (SWCNTs) in radial direction, while subjected to an axial and uniform magnetic field as well as a transient thermal field. Generalized plane strain state is considered in this study. The SWCNTs are assumed aligned, straight with infinite length. Two types of variations in the volume fraction of SWCNTs were considered in the structure of the FG cylinder along the radius from inner to outer surface, namely: functionally graded increasing (FG Inc) and functionally graded decreasing (FG Dec) which are then compared with uniformly distributed (UD) layouts. The constitutive equations of this type of reinforced polymeric cylinder are derived by Mori-Tanaka method. Following the introduction of a second order partial differential equation derived from the equations of motion and stress-strain relationships and solving by a semi-analytical method, distribution of stresses and perturbation of magnetic field vector are obtained. Results indicate that maximum radial and circumferential stresses occur in FG Inc and FG Dec layouts, respectively. Maximum perturbation of magnetic field vector is not affected by UD layout.
http://jsm.iau-arak.ac.ir/article_514396_fbea9973bac37207639511db86bbdcca.pdf
Magneto-thermo-elastic stresses
Perturbation of Magnetic Field Vector
FG SWCNTs
Cylinder
Transient thermal field
eng
Islamic Azad University Arak Branch
Journal of Solid Mechanics
2008-3505
2008-7683
2011-03-30
3
1
19
41
514397
Mechanical and Thermal Stresses in a FGPM Hollow Cylinder Due to Non-Axisymmetric Loads
M Jabbari
m_ jabbari@azad.ac.ir
1
M Meshkini
2
M.R Eslami
3
South Tehran Branch, Islamic Azad University
South Tehran Branch, Islamic Azad University
Department of Mechanical Engineering, Amirkabir University of Technology
In this paper, the general solution of steady-state two-dimensional non-axisymmetric mechanical and thermal stresses and mechanical displacements of a hollow thick cylinder made of fluid-saturated functionally graded porous material (FGPM) is presented. The general form of thermal and mechanical boundary conditions is considered on the inside and outside surfaces. A direct method is used to solve the heat conduction equation and the non-homogenous system of partial differential Navier equations, using the Complex Fourier Series and the power law functions method. The material properties, except of Poisson's ratio, are assumed to depend on the radial variable <em>r</em> and they are expressed as power law functions.
http://jsm.iau-arak.ac.ir/article_514397_52feeab5860c6a70b6fd76063036740c.pdf
Hollow cylinder
Non-Homogenous
Non-axisymmetric
FGPM
Navier equations
eng
Islamic Azad University Arak Branch
Journal of Solid Mechanics
2008-3505
2008-7683
2011-03-30
3
1
42
63
514398
Creep Life Forecasting of Weldment
J Jelwan
jad.jelwan@unsw.edu.au
1
M Chowdhry
2
G Pearce
3
Department of Mechanical Engineering and Manufacturing, University of New South Wales, Sydney, Australia
Department of Mechanical Engineering and Manufacturing, University of New South Wales, Sydney, Australia
Department of Mechanical Engineering and Manufacturing, University of New South Wales, Sydney, Australia
One of the yet unresolved engineering problems is forecasting the creep lives of weldment in a pragmatic way with sufficient accuracy. There are number of obstacles to circumvent including: complex material behavior, lack of accurate knowledge about the creep material behavior specially about the heat affected zones (HAZ),accurate and multi-axial creep damage models, etc. In general, creep life forecasting may be categorized into two groups, viz., those that are based on microscopic modeling and others that are based on macroscopic (phemenological) concepts. Many different micro-structural processes may cause creep damage .The micro-structural processes highlight the fact that the creep damages can be due to cavity nucleation and growth. Dislocation creep is another mechanism with micro-structural features such as sub-grain formation and growth, new phase formation, such as the Z phase, coarsening leading to the dissolution of the MX phase. This leads to the removal of pinning precipitates, which allow local heterogeneous sub-grain growth, weakening due to this growth and also to the dissolution of the MX. These features normally lead to the earlier formation of tertiary creep and reduced life. Considering welded joints ,the development of models for practical yet sufficiently accurate creep life forecasting based on micro-structural modeling becomes even more complicated due to variation of material in the base, weld and heat-affected-zone (HAZ) and variation of the micro-structure within HAZ and their interactions. So far, and until this date, none of the micro-structural models can forecast the creep life of industrial components with sufficient accuracy in an economic manner. There are several macroscopic (phemenological) models for creep life forecasting, including: time-fraction rule, strain-fraction rule, the reference stress and skeletal stress method, continuum damage model, etc. Each of which has their own limitations .This paper gauges to a multi-axial yet pragmatic and simple model for creep life forecasting weldment operating at high temperature and subjected to an elastic-plastic-creep deformation.
http://jsm.iau-arak.ac.ir/article_514398_8e161d03223fef26a1ad5c076ec9e821.pdf
Strain energy density
Finite element analysis
Creep
Weld
Stress/Strain analysis
Failure prediction
eng
Islamic Azad University Arak Branch
Journal of Solid Mechanics
2008-3505
2008-7683
2011-03-30
3
1
67
73
514399
Large Amplitude Vibration of Imperfect Shear Deformable Nano-Plates Using Non-local Theory
S.K Jalali
skjalali@ut.ac.ir
1
A Rastgoo
arastgo@ut.ac.ir
2
I Eshraghi
3
School of Mechanical Engineering, College of Engineering, University of Tehran
School of Mechanical Engineering, College of Engineering, University of Tehran
School of Mechanical Engineering, College of Engineering, University of Tehran
In this study, based on nonlocal differential constitutive relations of Eringen, the first order shear deformation theory of plates (FSDT) is reformulated for vibration of nano-plates considering the initial geometric imperfection. The dynamic analog of the von Kármán nonlinear strain-displacement relations is used to derive equations of motion for the nano-plate. When dealing with nonlinearities, in the frame work of nonlocal theory, challenges are presented because of the coupling between nonlocal stress resultants and displacement terms. Governing equations are solved using differential quadrature method (DQM) and numerical results for free vibration of an imperfect single layered graphene sheet are presented.
http://jsm.iau-arak.ac.ir/article_514399_cd47fac38be18cb6a72d90148884ce1f.pdf
Nonlocal theory
Shear Deformable Nano Plates
Nonlinear vibration
Geometric Imperfection
eng
Islamic Azad University Arak Branch
Journal of Solid Mechanics
2008-3505
2008-7683
2011-03-30
3
1
74
84
514400
Dynamic Characteristics and Vibrational Response of a Capacitive Micro-Phase Shifter
M Fathalilou
1
M Sadeghi
2
S Afrang
3
G Rezazadeh
g.rezazadeh@urmia.ac.ir
4
Mechanical Engineering Department, University of Tabriz
Mechanical Engineering Department, University of Tabriz
Electrical Engineering Department, Urmia University
Mechanical Engineering Department, Urmia University
The objective of this paper is to control the phase shifting by applying a bias DC voltage and changing the mechanical characteristics in electrostatically-actuated micro-beams. This problem can be more useful in the design of micro-phase shifters, which has not generally been investigated their mechanical behavior. By presenting a mathematical modeling, Galerkin-based step by step linearization method (SSLM) and Galerkin-based reduced order model have been used to solve the governing static and dynamic equations, respectively. The equilibrium positions or fixed pints of the system have been determined and the calculated static and dynamic pull-in parameters have been validated by previous experimental and theoretical results and a good agreement has been achieved. The frequency response of the system has been studied and illustrated that changing applied bias DC voltage affects the resonance frequency and maximum amplitude of the system vibrations. Then, phase diagram of the system for various damping ratio and excitation frequencies has been gained. It has been shown that by changing the bias DC voltage applied on the electrostatically-actuated micro-beam, which can be used as a varactor in phase shifter circuit, the stiffness of the micro-beam changes and consequently the phase shifting can be controlled. Finally, effect of the geometrical and mechanical properties of the micro-beam on the value of the phase shifting has been studied.
http://jsm.iau-arak.ac.ir/article_514400_86a4e8def62942e5c1aaa728fa37b0a8.pdf
MEMS
Phase shifter
Micro-beam
Electrostatic
Pull-in phenomena
eng
Islamic Azad University Arak Branch
Journal of Solid Mechanics
2008-3505
2008-7683
2011-03-30
3
1
85
95
514401
Hygrothermal Analysis of Laminated Composite Plates by Using Efficient Higher Order Shear Deformation Theory
S.K Singh
sushilbit@yahoo.co.in
1
A Chakrabarti
2
Department of Civil Engineering, Indian Institute of Technology
Department of Civil Engineering, Indian Institute of Technology
Hygrothermal analysis of laminated composite plates has been done by using an efficient higher order shear deformation theory. The stress field derived from hygrothermal fields must be consistent with total strain field in this type of analysis. In the present formulation, the plate model has been implemented with a computationally efficient C<sup>0 </sup>finite element developed by using consistent strain field. Special steps are introduced to circumvent the requirement of C<sup>1</sup>coninuity in the original plate formulation and C<sup>0 </sup>continuity of the present element has been compensated in stiffness matrix calculations. The accuracy of the proposed C<sup>0 </sup>element is established by comparing the results with those obtained by three dimensional elasticity solutions and other finite element analysis.
http://jsm.iau-arak.ac.ir/article_514401_0b78653684aa67e78da6308b9f1c0183.pdf
Finite Element
Higher order
Static Analysis
Laminated composites
Hygrothermal load
eng
Islamic Azad University Arak Branch
Journal of Solid Mechanics
2008-3505
2008-7683
2011-03-30
3
1
96
113
514402
Nonlinear Finite Element Analysis of Bending of Straight Beams Using hp-Spectral Approximations
R Ranjan
ranrakesh@gmail.com
1
SiViRT Center, University of Texas, San Antonio Department of Mechanical Engineering San Antonio
Displacement finite element models of various beam theories have been developed using traditional finite element interpolations (i.e., Hermite cubic or equi-spaced Lagrange functions). Various finite element models of beams differ from each other in the choice of the interpolation functions used for the transverse deflection <em>w</em>, total rotation <em>φ</em> and/or shear strain γ<sub>xz</sub>, or in the integral form used (e.g., weak form or least-squares) to develop the finite element model. The present study is concerned with the development of alternative beam finite elements using <em>hp</em>-spectral nodal expansions to eliminate shear and membrane locking. Both linear and non-linear analysis are carried out using both displacement and mixed finite element models of the beam theories studied. Results obtained are compared with both analytical (series) solutions and non-linear finite element solutions from literature, and excellent agreement is found for all cases.
http://jsm.iau-arak.ac.ir/article_514402_2ad9d83b9ba030e504a0d4e604a7fc73.pdf
spectral/hp method
Timoshenko Beam Theory
Euler-Bernoulli beam theory
Nodal expansions
Displacement and mixed finite element models