eng
Islamic Azad University Arak Branch
Journal of Solid Mechanics
2008-3505
2008-7683
2017-12-30
9
4
680
696
537797
Viscous Fluid Flow-Induced Nonlocal Nonlinear Vibration of Embedded DWBNNTs
A Ghorbanpour Arani
aghorban@kashanu.ac.ir
1
Z Khoddami Maraghi
2
R Kolahchi
3
M Mohammadimehr
4
Faculty of Mechanical Engineering, University of Kashan, Kashan, Iran--- Institute of Nanoscience & Nanotechnology, University of Kashan, Kashan, Iran
Faculty of Mechanical Engineering, University of Kashan, Kashan, Iran
Faculty of Mechanical Engineering, University of Kashan, Kashan, Iran
Faculty of Mechanical Engineering, University of Kashan, Kashan, Iran
In this article, electro-thermo nonlocal nonlinear vibration and instability of viscous-fluid-conveying double–walled boron nitride nanotubes (DWBNNTs) embedded on Pasternak foundation are investigated. The DWBNNT is simulated as a Timoshenko beam (TB) which includes rotary inertia and transverse shear deformation in the formulation. Considering electro-mechanical coupling, the nonlinear governing equations are derived using Hamilton’s principle and discretized based on the differential quadrature method (DQM). The lowest four frequencies are determined for clamped-clamped boundary condition. The effects of dimensionless small scale parameter, elastic medium coefficient, flow velocity, fluid viscosity and temperature change on the imaginary and real components of frequency are also taken into account. Results indicate that the electric potential increases with decreasing nonlocal parameter. It is also worth mentioning that decreasing nonlocal parameter and existence of Winkler and Pasternak foundation can enlarge the stability region of DWBNNT.
http://jsm.iau-arak.ac.ir/article_537797_f7741ce24c2f3a327cd6c87838e9e18b.pdf
Nonlinear vibration and instability
DWBNNTs
Pasternak foundation
Conveying viscous fluid
Piezoelasticity theory
eng
Islamic Azad University Arak Branch
Journal of Solid Mechanics
2008-3505
2008-7683
2017-12-30
9
4
697
706
537804
An Experimental Investigation on Fracture Analysis of Polymer Matrix Composite under Different Thermal Cycling Conditions
A.R Ghasemi
ghasemi@kashanu.ac.ir
1
M Moradi
2
Faculty of Mechanical Engineering, Department of Solid Mechanics, University of Kashan, Kashan, Iran
Faculty of Mechanical Engineering, Department of Solid Mechanics, University of Kashan, Kashan, Iran
Fracture analysis of glass/epoxy composites under different thermal cycling conditions is considered. Temperature difference, stacking sequence, fiber volume fraction and number of thermal cycles are selected as the experimental design factors. The Taguchi method is implemented to design of the experiment and an apparatus is developed for automatic thermal cycling tests. The tensile tests are done to study mechanical behavior of the specimens after the thermal cycling. The results show that the stacking sequence is the main effective factor on the fracture surface behavior of the specimens. Also, long splitting, lateral and angled breakage are the dominate failure mode of [0]<sub>8</sub>, [0<sub>2</sub>/90<sub>2</sub>]<sub>s</sub> and [0/±45/90]<sub>s</sub> layups, respectively. It’s found that the thermal cycling and temperature difference cause to increase the surface matrix loss significantly. This surface matrix loss can be an initial region to matrix debonding and crack propagation. Also, when the angle difference between lamina is increased the mechanical properties are reduced under the thermal cycling, significantly.
http://jsm.iau-arak.ac.ir/article_537804_1cb20d928aedd4cb502cb09819c2c753.pdf
Thermal cycling
Fracture of composite
Polymer matrix composites (PMCs)
Taguchi Method
eng
Islamic Azad University Arak Branch
Journal of Solid Mechanics
2008-3505
2008-7683
2017-12-30
9
4
707
729
537807
Nonlocal Piezomagnetoelasticity Theory for Buckling Analysis of Piezoelectric/Magnetostrictive Nanobeams Including Surface Effects
A Ghorbanpour Arani
aghorban@kashanu.ac.ir
1
M Abdollahian
2
A.H Rahmati
3
Faculty of Mechanical Engineering, University of Kashan, Kashan, Iran --- Institute of Nanoscience & Nanotechnology, University of Kashan, Kashan, Iran
Faculty of Mechanical Engineering, University of Kashan, Kashan, Iran
Faculty of Mechanical Engineering, University of Kashan, Kashan, Iran
This paper presents the surface piezomagnetoelasticity theory for size-dependent buckling analysis of an embedded piezoelectric/magnetostrictive nanobeam (PMNB). It is assumed that the subjected forces from the surrounding medium contain both normal and shear components. Therefore, the surrounded elastic foundation is modeled by Pasternak foundation. The nonlocal piezomagnetoelasticity theory is applied so as to consider the small scale effects. Based on Timoshenko beam (TB) theory and using energy method and Hamilton’s principle the motion equations are obtained. By employing an analytical method, the critical magnetic, electrical and mechanical buckling loads of the nanobeam are yielded. Results are presented graphically to show the influences of small scale parameter, surrounding elastic medium, surface layers, and external electric and magnetic potentials on the buckling behaviors of PMNBs. Results delineate the significance of surface layers and external electric and magnetic potentials on the critical buckling loads of PMNBs. It is revealed that the critical magnetic, electrical and mechanical buckling loads decrease with increasing the small scale parameter. The results of this work is hoped to be of use in micro/nano electro mechanical systems (MEMS/NEMS) especially in designing and manufacturing electromagnetoelastic sensors and actuators.
http://jsm.iau-arak.ac.ir/article_537807_f301078e1147033edac1fb5a576e032f.pdf
Magnetostrictive piezoelectric
Nanobeam
Surface effect
Nonlocal piezomagnetoelasticity theory
Buckling
eng
Islamic Azad University Arak Branch
Journal of Solid Mechanics
2008-3505
2008-7683
2017-12-30
9
4
730
750
537808
Coupled Bending-Longitudinal Vibration of Three Layer Sandwich Beam using Exact Dynamic Stiffness Matrix
A. Zare
zare@yu.ac.ir
1
B Rafezy
2
W.P Howson
3
School of Engineering, Yasouj University, Yasouj, Iran
Sahand University of Technology, Tabriz, Iran
Independent Consultant, Gwanwyn, Craig Penlline, CF71 7RT, UK
A Newtonian (vectorial) approach is used to develop the governing differential equations of motion for a three layer sandwich beam in which the uniform distribution of mass and stiffness is dealt with exactly. The model allows for each layer of material to be of unequal thickness and the effects of coupled bending and longitudinal motion are accounted for. This results in an eighth order ordinary differential equation whose closed form solution is developed into an exact dynamic member stiffness matrix (exact finite element) for the beam. Such beams can then be assembled to model a variety of structures in the usual manner. However, such a formulation necessitates the solution of a transcendental eigenvalue problem. This is accomplished using the Wittrick-Williams algorithm, whose implementation is discussed in detail. The algorithm enables any desired natural frequency to be converged upon to any required accuracy with the certain knowledge that none have been missed. The accuracy of the method is then confirmed by comparison with five sets of published results together with a further example that indicates its range of application. A number of further issues are considered that arise from the difference between sandwich beams and uniform single material beams, including the accuracy of the characteristic equation, co-ordinate transformations, modal coupling and the application of boundary conditions.
http://jsm.iau-arak.ac.ir/article_537808_129dcaa4478507b5a24d97aea6647aa2.pdf
Sandwich beam
Exact dynamic stiffness matrix
Coupled motion
Transcendental eigenvalue problem
Wittrick-Williams algorithm
eng
Islamic Azad University Arak Branch
Journal of Solid Mechanics
2008-3505
2008-7683
2017-12-30
9
4
751
759
537809
Three-Dimensional Finite Element Analysis of Stress Intensity Factors in a Spherical Pressure Vessel with Functionally Graded Coating
H Eskandari
eskandari@put.ac.ir
1
Abadan Institute of Technology, Petroleum University of Technology, Abadan, Iran
This research pertains to the three-dimensional (3D) finite element analysis (FEA) of the stress intensity factors (SIFs) along the crack front in a spherical pressure vessel coated with functionally graded material (FGM). The vessel is subjected to internal pressure and thermal gradient. The exponential function is adopted for property of FGMs. SIFs are obtained for a wide variety of crack shapes and layer thickness. The reported results clearly show that the material gradation of coating and the crack configuration can significantly affect the variation of SIFs along the crack front. The results are given which are applicable for fatigue life assessment and fracture endurance of FGM coating spherical pressure vessel and can be used in design purposes.
http://jsm.iau-arak.ac.ir/article_537809_f9a58a7aec028535b783c05ba9e5d8b0.pdf
Spherical pressure vessel
Functionally graded coating
Stress Intensity Factor
3D crack
Finite Element Analysis
eng
Islamic Azad University Arak Branch
Journal of Solid Mechanics
2008-3505
2008-7683
2017-12-30
9
4
760
782
537811
Exact Closed-Form Solution for Vibration Analysis of Truncated Conical and Tapered Beams Carrying Multiple Concentrated Masses
K Torabi
k.torabi@eng.ui.ac.ir
1
H Afshari
2
M Sadeghi
3
H Toghian
4
Department Mechanical Engineering, Faculty of Engineering, University of Isfahan, Isfahan, Iran
Department of Mechanical Engineering, Khomeinishahr Branch, Islamic Azad University, Khomeinishahr, Isfahan, Iran
Department of Solid Mechanics, Faculty of Mechanical Engineering, University of Kashan, Kashan, Iran
Department of Mechanical Engineering, Islamic Azad University, Najafabad Branch, Najafabad, Iran
In this paper, an exact closed-form solution is presented for free vibration analysis of Euler-Bernoulli conical and tapered beams carrying any desired number of attached masses. The concentrated masses are modeled by Dirac’s delta functions which creates no need for implementation of compatibility conditions. The proposed technique explicitly provides frequency equation and corresponding mode as functions with only two integration constants which leads to solution of a two by two eigenvalue problem for any number of attached masses. Using Basic functions which are made of the appropriate linear composition of Bessel functions leads to make implementation of boundary conditions much easier. The proposed technique is employed to study effect of quantity, position and translational inertia of the concentrated masses on the natural frequencies and corresponding modes of conical and tapered beams for all standard boundary conditions. Unlike many of previous exact approaches, presented solution has no limitation in number of concentrated masses. In other words, by increase in number of attached masses, there is no considerable increase in computational effort.
http://jsm.iau-arak.ac.ir/article_537811_6edbaf9801c6975ebfff3e1c93ad1ed1.pdf
Exact solution
Transverse vibration
Concentrated mass
Conical beam
Tapered beam
eng
Islamic Azad University Arak Branch
Journal of Solid Mechanics
2008-3505
2008-7683
2017-12-30
9
4
783
793
537813
Influences of Heterogeneities and Initial Stresses on the Propagation of Love-Type Waves in a Transversely Isotropic Layer Over an Inhomogeneous Half-Space
P Alam
alamparvez.amu@gmail.com
1
S Kundu
2
Department of Applied Mathematics, Indian Institute of Technology (Indian School of Mines), Dhanbad Jharkhand-826004, India
Department of Applied Mathematics, Indian Institute of Technology (Indian School of Mines), Dhanbad Jharkhand-826004, India
In the present paper, we are contemplating the influences of heterogeneities and pre-stresses on the propagation of Love-type waves in an initially stressed heterogeneous transversely isotropic layer of finite thickness lying over an inhomogeneous half space. The material constants and pre-stress have been taken as space dependent and arbitrary functions of depth in the respective media. To simplify the problem, we have used Whittaker’s function and separation of variables method. We present a general dispersion relation to describe the impacts on the propagation of Love-type waves in the structure. The present dispersion relation is analyzed case wise and also validated by comparison of the standard Love wave equation. Further, numerical computations are demonstrated graphically for the set of dimensionless parameters between dimensionless phase velocity and dimensionless wave number of the wave.
http://jsm.iau-arak.ac.ir/article_537813_7a683b9600c0397be2a1d0e3e9c2d006.pdf
Transversely
Isotropic
Heterogeneity
Phase velocity
Initial stress
eng
Islamic Azad University Arak Branch
Journal of Solid Mechanics
2008-3505
2008-7683
2017-12-30
9
4
794
801
537814
Mechanical Characteristics and Failure Mechanism of Nano-Single Crystal Aluminum Based on Molecular Dynamics Simulations: Strain Rate and Temperature Effects
R Rezaei
1
H Tavakoli-Anbaran
2
M Shariati
mshariati44@um.ac.ir
3
Faculty of Mechanical Engineering, Shahrood University of Technology, Shahrood, Iran
Faculty of Physics, Shahrood University of Technology, Shahrood, Iran
Department of Mechanical Engineering, Faculty of Engineering, Ferdowsi University of Mashhad, Mashhad, Iran
Besides experimental methods, numerical simulations bring benefits and great opportunities to characterize and predict mechanical behaviors of materials especially at nanoscale. In this study, a nano-single crystal aluminum (Al) as a typical face centered cubic (FCC) metal was modeled based on molecular dynamics (MD) method and by applying tensile and compressive strain loadings its mechanical behaviors were investigated. Embedded atom method (EAM) was employed to represent the interatomic potential of the system described by a canonical ensemble. Stress-strain curves and mechanical properties including modulus of elasticity, Poisson’s ratio, and yield strength were determined. Furthermore, the effects of strain rate and system temperature on mechanical behavior were obtained. It was found that the mechanical properties exhibited a considerable dependency to temperature, but they hardly changed with increase of strain rate. Moreover, nucleation and propagation of dislocations along the plane of maximum shearing stress were the mechanisms of the nanocrystalline Al plastic deformation.
http://jsm.iau-arak.ac.ir/article_537814_1533a47de8a42af880d582b01168f501.pdf
Nanocrystalline aluminum
Mechanical properties
Molecular Dynamics
Defromation mechanism
eng
Islamic Azad University Arak Branch
Journal of Solid Mechanics
2008-3505
2008-7683
2017-12-30
9
4
802
810
537815
Buckling Study of Thin Tank Filled with Heterogeneous Liquid
J El Bahaoui
jelbahaoui@yahoo.com
1
H Essaouini
2
L El Bakkali
3
Abdelmalek Essaadi Universty, Faculty of Science, M2SM Group ,93000 M’Hannech ,Tetuan, Morocco
Abdelmalek Essaadi Universty, Faculty of Science, M2SM Group ,93000 M’Hannech ,Tetuan, Morocco
Abdelmalek Essaadi Universty, Faculty of Science, M2SM Group ,93000 M’Hannech ,Tetuan, Morocco
Buckling of imperfect thin shell tank which is subjected to uniform axial compression is analyzed. The effect of internal pressure on the stability of a shell tank filled with a homogeneous-heterogeneous liquid was considered. Investigation of the liquid nature effect on reduction of the shell buckling load is performed by using the finite elements method. Calculating results in terms of analytical formula give a good agreement with the numerical results given by Abaqus when using actual measurements. The obtained results show the influence of the physical characteristics of liquid especially in the case of heterogeneous liquid. The study of combination between compression load, lateral pressure and the mechanical properties of liquid filling the tank is recommended for dimensioning the shell tanks to avoid the buckling phenomenon.
http://jsm.iau-arak.ac.ir/article_537815_bec3ae0b317018653627bfffd37966a0.pdf
Thin Shell tank
Buckling strenght
Homogeneous-heterogeneous liquid
Imperfection
Finit elements method
eng
Islamic Azad University Arak Branch
Journal of Solid Mechanics
2008-3505
2008-7683
2017-12-30
9
4
811
820
537816
Numerical and Experimental Study on Ratcheting Behavior of Plates with Circular Cutouts under Cyclic Axial Loading
K Kolasangiani
1
M Shariati
mshariati44@um.ac.ir
2
Kh Farhangdoost
3
A Varvani-Farahani
4
Department of Mechanical Engineering, Ferdowsi University of Mashhad, Mashhad, Iran
Department of Mechanical Engineering, Ferdowsi University of Mashhad, Mashhad, Iran
Department of Mechanical Engineering, Ferdowsi University of Mashhad, Mashhad, Iran
Department of Mechanicaland and Industrial Engineering, Ryerson University, Toronto, Canada
In this paper, accumulation of plastic deformation of AISI 1045 steel plates with circular cutouts under cyclic axial loading is studied. Loading was applied under force-control conditions. Experimental tests were performed using a Zwick/Roell servo hydraulic machine. Under force-control loading with nonzero mean force, plastic strain was accumulated in continuous cycles called ratcheting. Numerical analysis was carried out by ABAQUS software using nonlinear isotropic/kinematic hardening model. The results of the numerical simulations were compared to experimental data. The results demonstrated that the ratcheting response of plates with circular cutouts could be numerically simulated with a reasonable accuracy. It was observed that the local and global plastic deformation increase with increasing the notch diameter. Also, maximum principal stress was the main parameter for initiation of crack around the notch. Based on numerical results, at notch root, both ratcheting strain and local mean stress relaxation was occur simultaneously and due to relaxation of local mean stress, plastic shakedown was occurred.
http://jsm.iau-arak.ac.ir/article_537816_b8b377fc4c6d0c2347f93f1b381dc59a.pdf
Plate with circular cutout
Numerical and experimental study
Cyclic loading
Nonlinear isotropic/kinematic hardening model
eng
Islamic Azad University Arak Branch
Journal of Solid Mechanics
2008-3505
2008-7683
2017-12-30
9
4
821
831
537817
Biaxial Buckling Analysis of Symmetric Functionally Graded Metal Cored Plates Resting on Elastic Foundation under Various Edge Conditions Using Galerkin Method
M Rezaei
1
S Ziaee
ziaee@yu.ac.ir
2
S Shoja
3
Department of Mechanical Engineering, School of Engineering, Yasouj University, Yasouj, Iran
Department of Mechanical Engineering, School of Engineering, Yasouj University, Yasouj, Iran
Department of Civil Engineering, School of Engineering, Yasouj University, Yasouj, Iran
In this paper, buckling behavior of symmetric functionally graded plates resting on elastic foundation is investigated and their critical buckling load in different conditions is calculated and compared. Plate governing equations are derived using the principle of minimum potential energy. Afterwards, displacement field is solved using Galerkin method and the proposed process is examined through numerical examples. Effect of FGM power law index, plate aspect ratio, elastic foundation stiffness and metal core thickness on critical buckling load is investigated. The accuracy of this approach is verified by comparing its results to those obtained in another work, which is performed using Fourier series expansion.
http://jsm.iau-arak.ac.ir/article_537817_5a0f7ca5b1c2dd82c9f661f56e999784.pdf
Functionally graded material
Plate
Buckling analysis
Galerkin Method
Elastic foundation
eng
Islamic Azad University Arak Branch
Journal of Solid Mechanics
2008-3505
2008-7683
2017-12-30
9
4
832
848
537818
Investigating the Effect of Stiffness/Thickness Ratio on the Optimal Location of Piezoelectric Actuators Through PSO Algorithm
S Jafari Fesharaki
jafari@pmc.iaun.ac.ir
1
S.Gh Madani
2
S Golabi
3
Department of Mechanical Engineering, Najafabad Branch, Islamic Azad University, Najafabad, Iran
Department of Mechanical Engineering, Faculty of Engineering, University of Kashan, Kashan, Iran
Department of Mechanical Engineering, Faculty of Engineering, University of Kashan, Kashan, Iran
<span>This article has studied the effect of ratio of stiffness and thickness between piezoelectric actuators and host plat has been explored on optimal pattern for placement of piezoelectric work pieces around a hole in thin isotropic plate under static loading to reduce stress concentration. The piezoelectric actuators reduce directly or indirectly the stress concentration by applying positive and negative strains on the host plate. For this purpose, various modes as the thickness/stiffness ratios of the plate to the piezoelectric patches as ≥1 or ≤1 were considered. Then, a Python code was developed using particle swarm optimization algorithm in order to achieve the best model of piezoelectric actuators around the hole for maximum reduction in stress concentration factor. Also, the maximum stress concentration on the top and bottom of the hole was moved to another point around the edge by changing the location of piezoelectric patches. The results obtained from software solutions were confirmed by experimental tests. </span>
http://jsm.iau-arak.ac.ir/article_537818_69c67aedfc2f629d664c725b4462abd9.pdf
Optimization
Piezoelectric patches
Stiffness
particle swarm optimization
eng
Islamic Azad University Arak Branch
Journal of Solid Mechanics
2008-3505
2008-7683
2017-12-30
9
4
849
864
537819
Non-Linear Analysis of Asymmetrical Eccentrically Stiffened FGM Cylindrical Shells with Non-Linear Elastic Foundation
A.R Shaterzadeh
a_shaterzadeh@shahroodut.ac.ir
1
K Foroutan
2
Faculty of Mechanical Engineering, Shahrood University of Technology, Shahrood, Iran
Faculty of Mechanical Engineering, Shahrood University of Technology, Shahrood, Iran
In this paper, semi-analytical method for asymmetrical eccentrically stiffened FGM cylindrical shells under external pressure and surrounded by a linear and non-linear elastic foundation is presented. The proposed linear model is based on two parameter elastic foundation Winkler and Pasternak. According to the von Karman nonlinear equations and the classical plate theory of shells, strain-displacement relations are obtained. The smeared stiffeners technique and Galerkin method, used for solving nonlinear problem. To finding the nonlinear dynamic response of fourth order Runge-Kutta method is used. The effect of parameters asymmetrical eccentrically stiffened on the nonlinear dynamic buckling response of FGM cylindrical shells have been investigated.
http://jsm.iau-arak.ac.ir/article_537819_b0c5edf5d1daa4b3c0f4f776cd779d22.pdf
FGM cylindrical shells
Non-linear dynamic analysis
Asymmetrical stiffened
Non-linear elastic foundation
eng
Islamic Azad University Arak Branch
Journal of Solid Mechanics
2008-3505
2008-7683
2017-12-30
9
4
865
877
537820
An Investigation of Stress and Deformation States of Rotating Thick Truncated Conical Shells of Functionally Graded Material
A Thawait
amkthawait@gmail.com
1
L Sondhi
2
Sh Bhowmick
3
Sh Sanyal
4
Department of Mechanical Engineering, Institute of Technology, Guru Ghasidas Vishwavidyalaya, Bilaspur, 495009, India
Department of Mechanical Engineering, Shri Shankaracharya Technical Campus, SSGI, Bhilai, 490020, India
Department of Mechanical Engineering, National Institute of Technology (NIT), Raipur, 492010, India
Department of Mechanical Engineering, National Institute of Technology (NIT), Raipur, 492010, India
The present study aims at investigating stress and deformation behavior of rotating thick truncated conical shells subjected to variable internal pressure. Material prpperties of the shells are graded along the axial direction by Mori-tanaka scheme, which is achieved by elemental gradation of the properties.Governing equations are derived using principle of stsionary total potential (PSTP) and shells are subjected to clamped- clamped boundary conditions. Aluminum-zirconia, metal-ceramic and ceramic-metal FGM is considered and effects of grading index of material properties and pressure distribution are analyzed. Distribution of Radial displacement and circumferential stress in both radial and axial direction is presented. Further a comparison of behaviors of different FGM shells and homogeneous shells are made which shows, a significant reduction in stresses and deformations of FGM shells as compared to homogeneous shell. FGM shell having value of grading parameter <em>n</em> = 2 is most suitable for the purpose of rotating conical shells having variable pressure distribution as compared to homogeneous shell and shell having other values of grading parameter <em>n</em>.
http://jsm.iau-arak.ac.ir/article_537820_8ee39d619b838286502141cb1da1f40f.pdf
Rotating thick truncated conical shell
Functionally graded material
Linear elastic analysis
eng
Islamic Azad University Arak Branch
Journal of Solid Mechanics
2008-3505
2008-7683
2017-12-30
9
4
878
890
537821
Effect of Submerged Arc Welding Parameter on Crack Growth Energy on St37
J.A Khodaii
1
A Mostafapour
a-mostafapur@tabrizu.ac.ir
2
M.R Khoshravan
3
Department of Mechanical Engineering ,Amirkabir University of Technology, Tehran, Iran
Department of Mechanical Engineering ,University of Tabriz, Tabriz, Iran
Department of Mechanical Engineering ,University of Tabriz, Tabriz, Iran
In this article the influence of welding parameters such as electrical current, feed rate and stick out on crack growth energy was investigated. Therefore, prepared specimens were welded in various conditions. Using the Minitab software, 18 states of 36 possible states were chosen and applied. Then a crack was crated on the weld metal and the force-displacement diagram was plotted. Comparison of results shows that in high electricity current, the extra heat flux is the dominant factor, which causes coarse grains of microstructures. On the other hand, in low electricity current, lack of fusion and penetration reduce the crack propagation energy. Furthermore, the neural network could predict the amount of energy with high accuracy.
http://jsm.iau-arak.ac.ir/article_537821_7284c1bba59060aa053cc020221542a6.pdf
Submerged arc welding
Crack growth energy
Welding parameter
Optimization
eng
Islamic Azad University Arak Branch
Journal of Solid Mechanics
2008-3505
2008-7683
2017-12-30
9
4
891
904
537822
Extension of VIKOR Method to Find an Optimal Layout for Fixture's Supporting Points in Order to Reduce Work Piece Deformation
M Ehsanifar
m-ehsanifar@iau-arak.ac.ir
1
M Hemesy
2
Department of Industrial Engineering, Islamic Azad University, Arak Branch, Arak, Iran
Department of Industrial Engineering, Islamic Azad University, Arak Branch, Arak, Iran
In automotive industry fixtures have a direct effect on product manufacturing quality, productivity and cost, as a result fixtures, particularly welding fixture, play a crucial role in the auto industry. The fixture is a special tool for holding a work piece in proper position during manufacturing operation, so in the phase of the fixture design process positioning pins and surfaces are used to make sure that the work piece is positioned correctly and remain in the same position throughout the operation. The less positioning surfaces leads to the less work piece deformation. The aim of this paper is to find optimal number of positioning surfaces using VIKOR method with Shanon entropy concept to extract and utilize objective weights. VIKOR, means multi-criteria optimization and compromise solution, is a modern approach that has preference over other MCDM methods. An empirical example is presented to demonstrate an application of mentioned method.
http://jsm.iau-arak.ac.ir/article_537822_102e735a9a48fd1e9dd5630ae172d084.pdf
Fixture design
VIKOR Method
MCDM
ABAQUS
Supporting points